Tällä sivustolla käytetään evästeitä ja muita seurantatekniikoita tarjoamaan sinulle palveluja, parantamaan palvelujen suorituskykyä ja toiminnallisuutta, analysoimaan tuotteiden ja palvelujen käyttöä sekä auttamaan mainonnassa ja markkinoinnissa.

Evästekäytäntö   Tietosuojailmoitus

Edellinen Seuraava

Koulutus

ESABin osaamiskeskus

Siitä lähtien, kun Oscar Kjellberg keksi päällystetyn hitsauspuikon 1904, ESABilla on ollut olennainen rooli useamman yleisesti hyväksytyn hitsausprosessin keksimisessä ja kehittämisessä kuin millään muulla yhtiöllä.

ESABin osaamiskeskus sisältää valtavan määrän tietoa hitsaajalle, teknikolle, hitsaustarkastajalle ja projektinjohtajalle.

Choosing Welding Consumables

The tables are guides for choosing the correct welding consumable when welding similar or dissimilar materials. If the materials you need to join are not on the list, please contact us.

Joining Similar Materials The table gives typical selections of welding consumables and basic designations for wire electrodes and filler wire/rods. It does not indicate the silicon-alloyed variants used for MIG welding or the variants of covered electrodes or wire-flux combinations for submerged arc welding.

Base metal

Exaton Welding Consumable

ASTM/UNS

ISO

Exaton

Normal choice 1

Over-alloyed choice 1

304L2

1.43062

3R122

19.9.L (19.9.Nb)

19.12.3.L ...

The tables are guides for choosing the correct welding consumable when welding similar or dissimilar materials. If the materials you need to join are not on the list, please contact us.

Joining Similar Materials The table gives typical selections of welding consumables and basic designations for wire electrodes and filler wire/rods. It does not ...

Lue lisää

Handling and Storage of Welding Fluxes

By carefully selecting raw materials and optimizing manufacturing conditions the Exaton fluxes have guaranteed as-delivered moisture content from the factory.

Normally, the fluxes are delivered in steel drums, each containing 25 kg (55 lbs). Each pallet has a net weight of 500–1000 kg (1100–2200 lbs) and is shrink wrapped in plastic or packed in wooden crates before delivery from the factory.

To maintain the as-delivered moisture content, as long as possible, the handling and storage of the flux must be done according to the following requirements.

Transport

Transportation of the flux must be done in covered vehicles.

Unbroken pallets must be shrink wrapped in plastic or kept ...

By carefully selecting raw materials and optimizing manufacturing conditions the Exaton fluxes have guaranteed as-delivered moisture content from the factory.

Normally, the fluxes are delivered in steel drums, each containing 25 kg (55 lbs). Each pallet has a net weight of 500–1000 kg (1100–2200 lbs) and is shrink wrapped in plastic or packed in ...

Lue lisää

Shielding the Weld

Shielding the Weld The primary tasks of a shielding gas are to protect the weld pool from the influence of the atmosphere, i.e. from oxidation and nitrogen absorption, and to stabilize the electric arc. The choice of shielding gas can also influence the characteristics of the weld penetration profile.

Shielding Gas Protection Shielding gases for MIG/GMAW welding

The basic gas for MIG/MAG welding is argon (Ar). Helium (He) can be added to increase penetration and fluidity of the weld pool. Argon or argon/helium mixtures can be used for welding all grades. However, small additions of oxygen (O2) or carbon dioxide (CO2) are usually needed to stabilize the arc, improve the fluidity and ...

Shielding the Weld The primary tasks of a shielding gas are to protect the weld pool from the influence of the atmosphere, i.e. from oxidation and nitrogen absorption, and to stabilize the electric arc. The choice of shielding gas can also influence the characteristics of the weld penetration profile.

Shielding Gas Protection Shielding gases for ...

Lue lisää

Troubleshooting Guide

Problem Cause Solution Cracking centerline Excessive dilution Add more filler metal or use technique to achieve slightly convex weld bead. Check dissimiliar joining chart to make sure correct filler material is being used. Cracking Random Overstressed weld Lower amperage or voltage or increase travel speed to lower heat input, which causes distortion. Use step welding technique, change joint design. Keep the interpass temperature below 150°C (300°F). Cracking HAZ Usually base metal related Ensure not welding with machinable grade of material containing high levels of low melting intermetallics. Porosity Poor gas ...

Problem Cause Solution Cracking centerline Excessive dilution Add more filler metal or use technique to achieve slightly convex weld bead. Check dissimiliar joining chart to make sure correct filler material is being used. Cracking Random Overstressed weld Lower amperage or voltage or increase ...

Lue lisää

Welding Flux Basicity Index

Basicity is commonly used to describe the metallurgical behavior of a welding flux. The basicity index is a ratio between basic and acid compounds (oxides and fluorides) of which the flux is composed.

There are several ways of calculating basicity and in welding Boniszewski's formula has become the predominant way of calculating basicity.

Welding fluxes can be divided into three groups:  Type of welding flux   Basicity   Acid fluxes   <0.9   Neutral fluxes   0.9 - 1.2   Basic fluxes   >1.2 Basicity ...

Basicity is commonly used to describe the metallurgical behavior of a welding flux. The basicity index is a ratio between basic and acid compounds (oxides and fluorides) of which the flux is composed.

There are several ways of calculating basicity and in welding Boniszewski's formula has become the predominant way of calculating basicity.

Welding ...

Lue lisää


Yhteisö

Liity ESAB-yhteisöön! Pidä yhteyttä ESABiin Facebookissa, YouTubessa ja Twitterissä, niin tiedät mitä tapahtuu. Tutustu myynninedistämismateriaaliimme, valokuviimme, videoihimme ja muuhun tarjontaamme. Ota yhteyttä ja tutustu muihin faneihimme tai keskustele uusimmista postauksistamme ja julkistuksistamme.


Koulutus

Uskomme ESABilla, että onnistumme toiminnassamme vain tukemalla tuotteitamme ja palvelujamme huippulaadukkaalla koulutuksella. Koulutusohjelmamme sisältävät useita vaihtoehtoja, joissa tarjoamme tietoa koneista, niiden turvallisesta käytöstä sekä tuottavuuden lisäämisestä.



x
x

x

Loading..